Hi forum members
I have done full backup as part of the annual service. System throwing power management error after boot up. I have removed all the probes and rebooted. No error. I have connected a probe and power management error showing on the screen immediately pressed probe button. Any idea which part of the unit throwing this error...
Thank you for Javier and A. Sanchez. software reloaded. Checked all the cables and connections.checked front end boards and power supply modules... All seems to OK. the exact error screen shot as follows.
Error: Error on Power management
Action restart the system
Error in File.\I_Begrenzer\TxPowerToHW_DAST.cpp:436
Version Voluson E6 14.0.8.1685(Oct 2015,15.00.02)
Also I looked at log file and as follows:
Module:HRS
Symbol Full name:vTxPowerOff
Synbol:vTxPowrOff
Source: ,line 0
I am suspecting the power supply but also concern about front end beam former board..can any one tell me which is near possible after reading the above errors..
I have basic service manual.. not helping much ..please share a copy of proprietory manual if any forum members has one.. thank you in advance for further advice..
Hi sir think there is some problem power.supply ics or.controllers.it would.be well.known try inspect power.supply by some electronics repairman.And.there is.one.small possiblity that problem may be sourcing by hard drive.but it is some possiblity.
Thameen Ansari
Voluson E6 error
June 28, 2018 01:28
Hi forum members
I have done full backup as part of the annual service. System throwing power management error after boot up. I have removed all the probes and rebooted. No error. I have connected a probe and power management error showing on the screen immediately pressed probe button. Any idea which part of the unit throwing this error...
to rate and post a comment
Javier Abdulov
re: Voluson E6 error
June 28, 2018 03:03
have poblem on power supply maybe,lso you must reload system
to rate and post a comment
Ricardo A. Sanchez
re: Voluson E6 error
June 29, 2018 08:39
check connections on probe connector board and power supply
to rate and post a comment
Thameen Ansari
re: Voluson E6 error
July 01, 2018 12:48
Thank you for Javier and A. Sanchez. software reloaded. Checked all the cables and connections.checked front end boards and power supply modules... All seems to OK. the exact error screen shot as follows.
Error: Error on Power management
Action restart the system
Error in File.\I_Begrenzer\TxPowerToHW_DAST.cpp:436
Version Voluson E6 14.0.8.1685(Oct 2015,15.00.02)
Also I looked at log file and as follows:
Module:HRS
Symbol Full name:vTxPowerOff
Synbol:vTxPowrOff
Source: ,line 0
I am suspecting the power supply but also concern about front end beam former board..can any one tell me which is near possible after reading the above errors..
I have basic service manual.. not helping much ..please share a copy of proprietory manual if any forum members has one.. thank you in advance for further advice..
to rate and post a comment
Javier Abdulov
re: re: Voluson E6 error
July 02, 2018 10:24
Hi sir think there is some problem power.supply ics or.controllers.it would.be well.known try inspect power.supply by some electronics repairman.And.there is.one.small possiblity that problem may be sourcing by hard drive.but it is some possiblity.
to rate and post a comment
Thameen Ansari
re: Voluson E6 error
July 09, 2018 08:44
HI All
Thank you for your tech support... finally it is PS issue..
to rate and post a comment