Sell your scrap MRI magnets! Top prices, free shipping, and fast pickups. Don't let dust-collecting, idle assets go to waste. Contact: ryan.swiderski@cyclicmaterials.earth or call 437-826-1621
Jose Antonio Molins Gonzalez
May 12, 2025 04:04
Were having an issue with a Hitachi Airis Elite MRI system When scanning wrists the system fails to detect the resonance frequency with any coil Howev...
Horacio Jose Gomez
January 24, 2024 12:37
Hi I would like to know if the electrical isolation of Gradient Y between the coil and generic ground on Magnetom C system must be the same than Grad...
Aleksander Proof
March 17, 2017 08:19
Hi I have a problem with Magnetom Espree Several times a day and in the morning when I turn on the machine an error occurs Scanner Hardware Malfu...
Posted by an Anonymous April 28, 2015 09:27
Dear All Can we replace copley controls Gradient 262PN with Performance control GA300 without any issue what will be the cost of Both Gradient can ...
Pedro Zamora
July 04, 2013 08:39
HELLO EVERYBODY THIS IS PEZACO I NEED YOUR HELP FOR SOLVING PROBLEM WITH AN IMAGE ARTIFACT OF MRI MODEL ULTRA OF TOSHIBA I BEEN CHECKING CONTROL WIRE...
DirectMed Imaging specializes in Equipment Sales, Parts, and Support. Parts are in stock and available for immediate delivery. In-room MRI Upgrades are available now. (855) 463-3727 or sales@directmedimaging.com
Posted by an Anonymous October 06, 2014 08:32
Hi I am having problem in Airis-Mate installed software now system is not obtaining IPs and subnet mask from option softwares try to configure manua...
Aleksander Proof
March 29, 2017 10:21
I have a problem with MRI Siemens Magnetom Essenza When i turn on the system a message appears RF Safety Watchdog error Hardware error the Power Abs...
Dave Adams
April 30, 2012 10:04
We are performing the phantom scans on this system and would like to see a passing set of phantom images for this system that the ACR has acceptedDoes...
IGNATIOS SPINELIS
May 29, 2026 03:38
Hello I have replaced the battery in the NVRAM chip of the board but the data were lost in the first place due to dead battery I need the correct...
Posted by an Anonymous May 15, 2026 09:50
Hello everyone I am working on a Siemens Avanto which is currently in storage with only the cryo-compressor connected cabinets are not poweredconnect...
Extensive inventory of Philips & Siemens MRI & CT used-tested, refurbished parts. Knowledgeable Sales and Inventory Team. 90-Day Warranty. Bilingual Support. Competitive Pricing. Technical Support. ISO Certified. parts@keimedicalimaging.com
Johnny Barreto
July 31, 2023 04:16
I have a problem with the Magnetom C MRI system It doesnt allow to make any sequence It doesnt even allow Tune up The error messages are The system...
RASHID KHADDOUR
May 05, 2023 02:33
Hello I need help with the following How to transfer a GE open MRI from one place to another at low risk and cost Is there any available guide tu...
Nelson Pena
November 14, 2022 06:37
Hi Could someone give me some recommendation on how to improve the images to pass the low contrast tests or what adjustment should I make in the syst...
Abderrahim Felkat
May 27, 2026 09:58
Hello I have a problem when we start they system and try to scan on saving the series before scanning we get The download of a prescribed series fai...
no signal vga in hitachi mri airis 2
Qurat Ul Ain
March 26, 2013 10:44
i am having problem in hitachi mri airis 2 no vga cable cinnected or no signal cable is properly connected i reinsert all the bboards hcd2 worksta...