Over 90 Total Lots Up For Auction at One Location - WA 04/08

Change Fuji FCR XC1 ip addresses

(3)

Derek Smith

Change Fuji FCR XC1 ip addresses

October 17, 2011 11:27

I need to change the IP addresses on the fujifilm XC 1 reader. Not the CPU, but the reader itself. Please advise.

Log inor Register

to rate and post a comment

Robert Budach

Re: Change Fuji FCR XC1 ip addresses

October 17, 2011 05:09

Configuration of Dedicated IIP to SMART CR (XG-1)

NOTE: The Smart CR / XG-1 / CR-IR346 must have a dedicated IIP or “host” IIP in order to function. Other IIP’s can be configured to work with the Smart but the host IIP must be funtional first.

To configure this IIP use the following steps:

1.) Make sure the IIP and Smart are connected with a crossover and both units are powered on.

2.)From the IIP Desktop GO TO: CR346 User utility
3.)Select NEW then enter desired Name and IP address:
NOTE: Default IP for the IIP is 172.16.1.20 Default IP for the Smart CR346 is 172.16.1.10

4.)Select OK

5.)You will be prompted for the Smart CR software CD. Insert the CD and select Install.Select the latest version A10 then select Install.

6.)Two PC-MUTL windows will appear.
Close the tool labeled PC-MUTL and select the latest version A10 in the PC-MUTL 1.4 window
then press OK

7.)In the config window enter the appropriate ip addresses and subnet. The IIP and FTP Server addresses must match. Do not change any other configuration items and MOST IMPORTANTLY, NEVER Shut down the smart or IIP while software is loading. This can damage the Smart CPU and it will have to be replaced. After entering configuration entries select SET.

8.)Smart will beep with flashing light and the progress of the installation will display in a status bar on the IIP. When PC-MUTL 1.4 window displays “Complete” select OK.
9.)At this point, the Smart and IIP may disconnect and not recognize each other on the network if the IP addresses had been changed in the Smart but not the IIP. To function properly, change the IIP address by going to Network places > Right mouse > Local Area Connection > Right Mouse > properties > General Tab > TCP/IP > Properties. Change IP , Subnet , Gateway as required.
10.)Go to Setup Configuration Item > Network Config > All other nodes > ru0 (or current hostname of Smart CR) Change IP to match CR.

11.)Complete STEP IX to completely enable the Smart CR to IIP

12.)When the Fuji application is started, the IIP should recognize the Smart and it will reinitialize. The connection is confirmed when the left display illuminates on the Smart CR and the toolbar on the application displays the RU (Smart CR) status.


1 person liked this
Log inor Register

to rate and post a comment

(3)

Derek Smith

Re: Change Fuji FCR XC1 ip addresses

October 18, 2011 10:54

Thank you very much, although I am working on the XC1, circa 2007, and the process you laid out was for the XG1. Is it the same regardless of XG1 or XC1?

Log inor Register

to rate and post a comment

Robert Budach

Re: Change Fuji FCR XC1 ip addresses

October 18, 2011 10:58

I believe the XC1 is the carbon. If this is the case, I do believe this is the same setups. \\

I will look further into this.

Log inor Register

to rate and post a comment

(77)
(13)
(2)

Gery Rodriguez

re: Re: Change Fuji FCR XC1 ip addresses

May 25, 2012 10:38

Same steps.

Log inor Register

to rate and post a comment

Robert Budach

Re: Change Fuji FCR XC1 ip addresses

October 18, 2011 10:58

I have a service manual for what I think is your reader. email me and I will send it to you.
rbudach@cox.net

Log inor Register

to rate and post a comment

(67)
(3)

farhan zeb

Re: Change Fuji FCR XC1 ip addresses

November 21, 2011 10:25

SIR i need the service manual and service software for fuji FM-Dpl

Log inor Register

to rate and post a comment

(2)
(1)

kim jonggi

re: Re: Change Fuji FCR XC1 ip addresses

January 04, 2014 08:40

I want service manual
my E-mail k019019@naver.com
thank you .

Log inor Register

to rate and post a comment

(28)
(4)

MOI

re: Re: Change Fuji FCR XC1 ip addresses

November 20, 2015 05:54

dear Sir. today i have receiv XG1 fugi with NETPIX but i need Service manual of XG1 and Netpix. Do you have this documentation ?? yes ! it is possible to have copie to me ! thanks in advance

Log inor Register

to rate and post a comment

(45)
(1)

chalie alvarez

re: Re: Change Fuji FCR XC1 ip addresses

August 10, 2012 09:08

do you have casettes for this units xg-1 i need a set of these ones new or if used in verry good conditions

Log inor Register

to rate and post a comment

(28)
(4)

MOI

re: Re: Change Fuji FCR XC1 ip addresses

November 20, 2015 05:54

Dear Robert. i must connect XG1 with Netpix, but i don't have the Technical manual. If you have it, it is possible for you to send copie to me. Thanks in advance , >Regards Roger

Log inor Register

to rate and post a comment

(139)
(14)
(4)

Miguel Chavira

re: Re: Change Fuji FCR XC1 ip addresses

January 07, 2021 09:52

Hi
Do you know how i to reset the ip to set the default ip ? 172.16.1.10
Make a hardwire
Thank you

Log inor Register

to rate and post a comment

stats
DOTmed text ad

Adepto Medical - Friendly, Full-Service IV Pump Sales, Rental, and Repair

Adepto Medical is an infusion pump rental, sales, and service company. Our focus is to deliver to our customers the best product and customer service support we can offer. Call (913) 261-9933

DOTmed Certified stats
advertisement

Upcoming Auction Events

NorthWest Supply
TIMED
Apr 08, 2024 (98 lots)